Made In Great Britain

Direct from our factory

Free Next Day Delivery

On orders over £750

Product Test Results

All test results published

Expert Technical Advice

Call or chat with our team

Everest Trade - Imprimación Epoxi de Alta Penetración / Sellador - Recubrimiento Epoxi de Dos Componentes

Key Product Features

100% Solids

Solvent free, no shrinkage

Deep Penetrating

Binds Weak Concrete

High Build Formula

Up to 5x thicker

Heavy Duty

Forklift Ready

Everest Trade - Imprimación Epoxi de Alta Penetración / Sellador - Recubrimiento Epoxi de Dos Componentes

100% Solids EpoxyHigh Adhesion2 Pack SystemDeep Penetrating

DESCRIPCIÓN DEL PRODUCTO
Un imprimador y sellador para suelos de dos componentes de alta calidad, fabricado para ser aplicado antes de las pinturas para suelos epoxi de dos componentes de Everest, adecuado para su uso en concreto nuevo una vez seco, concreto viejo friable, basado en una resina epoxi de alto espesor y libre de solventes, ideal para su uso en áreas domésticas e industriales como almacenes, fábricas, garajes y unidades industriales debido a su fórmula de alto espesor y alta durabilidad.

Recomendamos encarecidamente lijar el suelo antes de la aplicación para asegurar que el sellador y la pintura posterior se adhieran correctamente, garantizando un recubrimiento duradero.


Everest Trade - Pintura Epoxi para Suelos HB - Alto Espesor - Antideslizante es 100% sólidos, a diferencia de otras epoxis más baratas a base de agua y solventes. Esto resulta en ninguna pérdida de espesor de recubrimiento durante el curado, ayudando a proporcionar un recubrimiento más grueso y duradero.

Everest Trade - Pintura Epoxi para Suelos HB puede mejorar el suelo de su fábrica tanto en resistencia como en apariencia, proporcionando un acabado de brillo premium y aumentando la durabilidad general en parte debido al grosor del producto, que es hasta 5 veces más grueso que otros sistemas de pintura en el mercado y la resistencia mecánica general como resultado de la fuerza de la resina epoxi en sí.

Alta durabilidad contra la abrasión, arañazos e impactos, así como el desgaste mecánico de carretillas elevadoras, transpaletas y otras fuerzas mecánicas.

Proporciona un acabado resistente a la gasolina y al aceite con excelente durabilidad, además de ofrecer buenas propiedades de agarre de neumáticos, ideal para áreas con carretillas elevadoras y vehículos de trabajo.

Ideal para su uso en grandes fábricas, unidades industriales, garajes y suelos de talleres.

FABRICADO EN INGLATERRA CON RESINAS EPOXI PREMIUM. SEGÚN LAS NORMAS ISO 9001, GARANTIZANDO CALIDAD.

Este artículo siempre está en stock para todos los tamaños de pedido, entrega rápida en cualquier cantidad, importante si tiene una gran área que cubrir.


SUSTRATOS ADECUADOS
Se puede usar en concreto, metal y madera correctamente preparados (ver pestaña de aplicación arriba), así como en la mayoría de los otros sustratos porosos.
Por favor, consulte la pestaña de aplicación (arriba) para más detalles.

No se recomienda su uso en suelos autonivelantes, ya que tienden a ser no porosos.


COLOR
Se suministra en un acabado satinado gris claro.


RENDIMIENTO (Cobertura)
Una lata de 5 kg cubrirá aproximadamente 20-25+ metros cuadrados por capa. Las tasas de cobertura varían dependiendo del área de superficie y la porosidad.


TIEMPO DE SECADO/CURADO
Recomendamos permitir un mínimo de 24 horas a 20°C antes de permitir el tránsito peatonal y 48 horas a 20°C antes de permitir el tránsito vehicular en la(s) área(s) recubierta(s).

En circunstancias normales, este producto estará

Tiempo Libre de Tacto en aproximadamente 8-12 horas (a 20°C)
Tiempo de Secado Completo en aproximadamente 12-24 horas (a 20°C)

Las temperaturas por debajo de 20°C ralentizarán los tiempos de curado.


RESISTENCIA QUÍMICA
Este producto exhibe una excelente resistencia a ácidos diluidos, álcalis y aceites. Adecuado para la mayoría de los derrames industriales.


PRECAUCIONES DE ALMACENAMIENTO
Almacenar lejos del calor y las llamas. Asegure la tapa entre usos para evitar que la pintura se endurezca.
Mantener alejado de las heladas.

¡Disponible! Listo para enviar
£105.37
Configuration
Tamaño
Tamaño: 5kg

Delivery & Technical Support

Same Day Dispatch (Order by 11am)

Buy Direct From The Manufacturer

We Deliver To Mainland Europe

Technical Support From Coating Specialists

Our technical team can assist with product selection, surface preparation and application guidance.

Contact Technical Support

Key Product Features

100% Solids

Solvent free, no shrinkage

Deep Penetrating

Binds Weak Concrete

High Build Formula

Up to 5x thicker

Heavy Duty

Forklift Ready

Turns an absorbent slab into a sound, sealed base

Prime DP carries no solvent — the full 100% of what you apply penetrates the concrete and cures in place, consolidating the surface layer rather than forming a film on top of it. Porous floors take their finish evenly instead of absorbing it unevenly.
Click an icon to explore features Tap an icon to explore features
Everest Trade - Imprimación Epoxi de Alta Penetración / Sellador - Recubrimiento Epoxi de Dos Componentes

Abrasion Resistant Finish

A tough, semi-gloss satin finish engineered to withstand heavy foot traffic and abrasion. Enriched with UV-stable pigments, it maintains rich color depth and resists fading, making it equally effective for internal floors and external patios.

Hydrophobic Vapor Valve

The advanced acrylic lattice acts as a "one-way valve." It blocks rain and surface oils from penetrating downwards but allows trapped ground moisture to escape as vapor—preventing the bubbling and blistering common with standard floor paints.

Active Silane Adhesion

Unlike standard paints that sit on the surface, this formula uses silane promoters to chemically cross-link with the mineral substrate. This creates a permanent, rooted bond that resists flaking and peeling, even under duress.

Optimized Curing Profile

Engineered for efficient application cycles. The coating becomes touch-dry in just 2–4 hours (temperature dependent), preventing debris pickup and allowing for a reliable, streamlined application process on large surface areas.

Performance Profile

Professional grade two-pack solvent-free epoxy primer. A 100% solids clear epoxy that penetrates and stabilises porous and absorbent concrete, delivering a sealed, sound base for the coating system above. Single-coat application, with a defined pot life of up to 45 minutes at 20°C once the two parts are combined.

Download Data Sheet
Solids Content 100%Solvent-free — nothing lost to evaporation
Coverage 3-4m² per kgVaries with substrate porosity
Pot Life 45 minutesAt 20°C, from addition of the activator
Overcoat 8 hoursTouch dry in 6 hours

Essential Information

Product Details

Description

EverFlor Prime DP is a clear, two-pack, solvent-free epoxy floor primer formulated for the stabilisation of porous and absorbent concrete. It is the preparation stage in an EverFlor floor build-up — the coat that turns an open slab into a sound, sealed substrate ready to receive a finish.

Porous concrete is the most common cause of a disappointing floor coating. Prime DP is a 100% solids formulation, so everything you apply stays in and on the floor and nothing flashes off as solvent. It penetrates the surface and cures within it, consolidating the top layer of the concrete instead of bridging over it.

Supplied clear in a 5kg two-pack unit. Mix the two components by weight, apply one coat over normal porous concrete, then overcoat with your chosen EverFlor floor finish once the priming coat has hardened. As a reactive epoxy it has a defined working window once the activator goes in, so set the area out and mix only when you are ready to apply.

Recommended areas of use

  • Porous concrete floors
  • Absorbent concrete substrates requiring stabilisation before coating
  • As the priming stage of an EverFlor floor coating build-up

Features

  • Clear, solvent-free two-pack epoxy — 100% solids, so nothing is lost to evaporation
  • Penetrates and consolidates the top layer of the slab rather than forming a surface film
  • Seals absorbency so the finish coat cures with even gloss and full adhesion
  • Ready to use straight from the tin — no thinning required
  • One coat covers normal porous concrete
  • Applies by medium pile roller, cut in with a brush
  • Overcoat the same day or the next, with foot traffic possible after 8 hours at 20°C
  • 12 month shelf life in unopened units

Good to know

The substrate must be sound, clean and dry before priming. Apply between 10°C and 25°C, and store the unit in a cool, dry area. Do not allow the product to freeze. Because Prime DP is mixed by weight at 100:60 (A:B), do not split the unit into smaller quantities, as an inaccurate ratio can cause the product to fail to cure. Clean tools with warm soapy water immediately after use, before the epoxy begins to harden.

Application

SURFACE PREPARATION

Mechanically prepare the concrete before you prime. Grinding or abrading removes laitance, curing residues and any failing coating, and opens the surface so the epoxy can penetrate. Remove loose and flaking material back to sound substrate. Sweep and then vacuum the whole area — dust left on the slab will sit between the primer and the concrete and cost you adhesion.

MIXING

Mix the full 5kg unit as supplied. Do not split the pack or decant part quantities, as the ratio between the two parts must be maintained for a full cure. Use a mixing paddle on a slow-speed drill and keep the paddle below the surface of the material to avoid whipping air into it. Mix to a uniform consistency, then pour the material into a scuttle or roller tray and begin work straight away. The pot life is up to 45 minutes at 20°C from the moment the two parts are combined.

APPLICATION

Apply one coat by roller, cutting in at edges and around detail with a brush. The product is ready to use — do not thin it. Spread at 3-4m² per kg, allowing for more material where the concrete is markedly absorbent. Feed porous patches until they are evenly wetted out, then move on; the primer is not intended to be built up as a thick film.

DRYING AND OVERCOATING

Prime DP is touch dry in 6 hours and ready to receive the next coat after 8 hours. Overcoat within 48 hours at 20°C. Store unopened units in dry conditions; shelf life is 12 months.

Coverage Calculator
Technical Data
Finish Clear / transparent
Coverage 3-4m² per kg
Recommended coats 1
Touch dry 6 Hours at 20°C
Recoat after 8 Hours at 20°C
Application Medium pile roller. Cut in using a brush
Cleaner / Thinner Not required — apply as supplied
Suitable substrates Porous concrete floors, Absorbent concrete substrates requiring stabilisation before coating.
Shelf life 12 months
Pot life Up to 45 minutes at 20°C
Mixing ratio 100 : 60 by weight (A : B)
Application temperature Between 10°C - 25°C
Solids content 100%
Storage conditions Store in cool, dry area. Avoid frost.
Cleaning tools Warm soapy water
Wet film thickness 220 microns
Dry film thickness 220 microns
Number of components 2
Maximum overcoat 48 hours at 20°C
Principal limitations Floors must be prepared correctly to ensure good adhesion.
Foot traffic 8 Hours at 20°C
Files & Data Sheets

The Knowledge Hub

Everything You Need to Know

Browse our collection of in-depth articles and how-to guides designed to help you get the most out of this product. whether you need help with surface preparation or application advice, we have you covered.

View Technical Hub

A visual comparison of a mossy, weed-infested block paving driveway next to a freshly cleaned section in the UK.
  • por Sam Marriott

Restoring Block Paving: Removing Moss, Weeds, and Lichen

Block paving is the most popular driveway choice in the UK, but it has a major design flaw: Joints. Those thousands of gaps between the bricks are the perfect nursery for weeds, moss, and the dreaded "black spot" lichen. Every...

Leer más

An unbranded industrial floor scrubber being used to maintain the high-gloss shine on a polished concrete warehouse floor.
  • por Sam Marriott

Deep Cleaning Polished Concrete Without Damaging the Shine

Polished concrete is often sold as the "maintenance-free" flooring option. That is a lie. Yes, it is incredibly durable. It won't peel or flake like paint. But if you ignore it, or worse - if you clean it with the...

Leer más

Two unbranded silver tins labeled Acid and Alkaline on an industrial concrete warehouse floor.
  • por Sam Marriott

Acid vs. Alkaline Concrete Cleaners: Which is Best for Your Floor?

If you walk into a hardware store and ask for "concrete cleaner," you'll probably end up with a few different options in-front of you. Most people grab the bottle with the most aggressive warning label, thinking "stronger is better." But...

Leer más

How to Sand a Painted Concrete Floor for Recoating
  • por Sam Marriott

How to Sand a Painted Concrete Floor for Recoating

In our Sanding vs. Grinding: Preparing Previously Painted Concrete guide, we established that if your floor passes the Cross-Hatch Adhesion Test, then the next step for recoating will be sanding. Choosing to sand rather than grind saves you hundreds of pounds in equipment rental and diamond consumables....

Leer más

FAQs

Please read our FAQs page to find out more.

Why does porous concrete need priming before a floor coating?
An absorbent slab draws the binder out of the first coat as it is applied. That leaves dry patches, uneven gloss and a bond that never fully develops. Prime DP penetrates and seals the surface first, so the finish coat retains its binder and adheres properly.
How many coats of Prime DP do I need?
Apply one coat over normal porous concrete. Coverage is 3-4m² per kg, so a 5KG unit primes in the region of 15-20m² depending on how absorbent the slab is.
Does Prime DP need thinning?
No. Prime DP is supplied ready to use straight from the tin and requires no thinner. It is a 100% solids, solvent-free formulation.
How long do I have to work once the product is mixed?
Pot life is up to 45 minutes at 20°C from the moment you add the activator. Plan the area, set your tools out and mix only when you are ready to apply. On larger floors, break the job into sections you can complete inside that window.
When can I apply the finish coat?
Prime DP is touch dry in six hours and ready to overcoat after eight hours. That timing lets a prime-and-coat sequence run through the same day or into the next.

Didn’t find your answer?

Don't hestitate to contact us